收藏本站
Not Recommended for New Designs - Replaced by BCM48Bx320y300A00
Application Note
B048F320T30
Parallel Operation
The BCM ? bus converter will inherently current share when operated in
an array. Arrays may be used for higher power or redundancy in an
application.
Current sharing accuracy is maximized when the source and load
impedance presented to each bus converter within an array are equal.
The recommended method to achieve matched impedances is to
dedicate common copper planes within the PCB to deliver and return
the current to the array, rather than rely upon traces of varying lengths.
In typical applications the current being delivered to the load is larger
than that sourced from the input, allowing traces to be utilized on the
input side if necessary. The use of dedicated power planes is, however,
preferable.
The bus converter power train and control architecture allow bi-
directional power transfer, including reverse power processing from the
module output to its input. Reverse power transfer is enabled if the
module input is within its operating range and the module is otherwise
enabled. The bus converter’s ability to process power in reverse
improves the module’s transient response to an output load dump.
Thermal Considerations
VI Chip products are multi-chip modules whose temperature
distribution varies greatly for each part number as well as with the
input /output conditions, thermal management and environmental
conditions. Maintaining the top of the B048F320T30 case to less than
100°C will keep all junctions within the module below 125°C for most
applications. The percent of total heat dissipated through the top
surface versus through the J-lead is entirely dependent on the particular
mechanical and thermal environment. The heat dissipated through the
top surface is typically 60%. The heat dissipated through the J-lead
onto the PCB board surface is typically 40%. Use 100% top surface
dissipation when designing for a conservative cooling solution.
It is not recommended to use a module for an extended period of time
at full load without proper heat sinking.
Input Impedance Recommendations
To take full advantage of the BCM bus converter capabilities, the
impedance presented to its input terminals must be low from DC to
approximately 5 MHz. The source should exhibit low inductance and
should have a critically damped response. If the interconnect inductance
is excessive, the module input pins should be bypassed with an RC
damper (e.g., 47 μF in series with 0.3 ohm) to retain low source
impedance and proper operation. Given the wide bandwidth of the
module, the source response is generally the limiting factor in the
overall system response.
Anomalies in the response of the source will appear at the output of
the module multiplied by its K factor. The DC resistance of the source
should be kept as low as possible to minimize voltage deviations. This is
especially important if the module is operated near low or high line as
the overvoltage /undervoltage detection circuitry could be activated.
Input Fuse Recommendations
VI Chip modules are not internally fused in order to provide flexibility in
configuring power systems. However, input line fusing of the modules
must always be incorporated within the power system. A fast acting
fuse should be placed in series with the +In port.
BCM ? Bus Converter
Page 10 of 12
Rev 2.9
01/2014
vicorpower.com
800 927.9474
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX4824ETP+ IC 8CH RELAY DVR PWR SAVE 20TQFN
B048F240T30-EB EVAL BOARD 24V OUT 300W SMD
GEM08DRYI-S13 CONN EDGECARD 16POS .156 EXTEND
A9AAT-1806F FLEX CABLE - AFE18T/AF18/AFE18T
RO-0515S/P CONV DC/DC 1W 05VIN 15VOUT
RO-0512S/P CONV DC/DC 1W 05VIN 12VOUT
RO-0509S/P CONV DC/DC 1W 05VIN 09VOUT
B048F160T24-EB EVAL BOARD 16V OUT 240W SMD
相关代理商/技术参数
B048F480M30 功能描述:BCM BUS CONVERTER 48V 300W RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, BCM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）
B048F480M30A 功能描述:BCM BUS CONVERTER 48V 300W 制造商:vicor corporation 系列:VI Chip? BCM? 包装:散装 零件状态:有效 类型:总线转换器模块 输出数:1 电压 - 输入（最小值）:38V 电压 - 输入（最大值）:55V 电压 - 输出 1:48V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:6A 功率（W） - 制造系列:300W 电压 - 隔离:2.25kV（2250V） 应用:ITE（商业） 特性:远程开/关，OCP，OTP，OVP，SCP，UVLO 安装类型:表面贴装 封装/外壳:模块 大小/尺寸:1.28" 长 x 0.87" 宽 x 0.26" 高（32.5mm x 22.0mm x 6.7mm） 工作温度:-55°C ~ 125°C 效率:96.2% 功率（W） - 最大值:300W 标准包装:1
B048F480T30 功能描述:CONVERTER BUS 48V OUT 300W SMD RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, BCM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）
B048F480T30_11 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:Bus Converter
B048F480T30A 功能描述:BCM BUS CONVERTER 48V 300W 制造商:vicor corporation 系列:VI Chip? BCM? 包装:散装 零件状态:有效 类型:总线转换器模块 输出数:1 电压 - 输入（最小值）:38V 电压 - 输入（最大值）:55V 电压 - 输出 1:48V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:6A 功率（W） - 制造系列:300W 电压 - 隔离:2.25kV（2250V） 应用:ITE（商业） 特性:远程开/关，OCP，OTP，OVP，SCP，UVLO 安装类型:表面贴装 封装/外壳:模块 大小/尺寸:1.28" 长 x 0.87" 宽 x 0.26" 高（32.5mm x 22.0mm x 6.7mm） 工作温度:-40°C ~ 125°C 效率:96.2% 功率（W） - 最大值:300W 标准包装:1
B048F480T30-EB 功能描述:EVAL BOARD 48V OUT 300W SMD RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:V-I Chip™, BCM™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
B048G120T10 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI Chip - BCM Bus Converter Module
B048G120T15 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI Chip - BCM Bus Converter Module